Search

Hot Environments - Control Measures

On this page


How can I measure occupational heat stress exposure?

Back to top

Feeling hot or cold depends on:

  • Air temperature.
  • Relative humidity of the air.
  • Presence of hot or cold objects in the surrounding area.
  • Presence of air movement (breeze, ventilation).
  • Physical exertion.
  • Clothing.

Various methods of measuring occupational heat exposure combine these environmental factors to obtain a single number as a measure of overall heat load. The most used measure in the workplace is the wet bulb globe temperature (WBGT) index.

Please Note: This OSH Answers document contains information on the prevention of and control of heat-related illnesses. Please see Hot Environments - Health Effects and First Aid for information about the effects on the body from working in hot environments.

The Wet Bulb Globe Temperature (WBGT)
The wet bulb globe temperature is calculated using a formula that takes into account air temperature, speed of air movement, radiant heat from hot objects, sunshine, and body cooling due to sweat evaporation.

Air temperature is measured using a conventional thermometer.

The contribution due to radiant heat is measured using a black globe thermometer. A conventional thermometer is inserted through a rubber stopper into a hollow, six-inch diameter copper ball which is coated with a flat black paint. The thermometer bulb is positioned at the centre of the copper ball. The black globe thermometer normally requires at least 20 minutes to come to equilibrium reading.
The cooling effect of evaporation and air movement is taken into account using a natural wet bulb thermometer. A natural wet bulb thermometer is a conventional thermometer with its bulb wrapped with an absorbent cotton wick. The wick extends 30 to 35 millimetres above the thermometer bulb, and the lower end of the wick is immersed in distilled water. About 25 mm of moistened wick is exposed between the water and the bulb of the thermometer. The moist wick continuously provides water for evaporation. As with the black globe thermometer, the natural wet bulb thermometer also requires at least 20 minutes to reach equilibrium.

Two different methods are used to calculate WBGT in the workplace: one for workplaces with direct sunlight, and the other for workplaces without direct sunlight.

When conditions of the workplace fluctuate widely, time-weighted WBGT is often used. The question below "How do I calculate the WBGT Index?" gives examples of WBGT calculations. WBGT direct reading meters, often called heat stress analyzers, are also available - these meters give direct WBGT reading and no calculations are necessary.


What are exposure limits for heat stress?

Back to top

Exposure limits intended to minimize the risk of heat-related illnesses are set by provincial and territorial governments for most Canadian workplaces, and by Employment and Social Development Canada (ESDC) for workplaces under the federal jurisdiction. These agencies generally use the exposure (heat stress) guidelines recommended by the American Conference of Governmental Industrial Hygienists (ACGIH).

ACGIH defines heat stress as the net heat load to which a worker may be exposed from the combined contributions of metabolic heat, air temperature, air movement, humidity, radiant energy, and clothing.

Heat strain is defined by ACGIH as the overall physiological response resulting from heat stress.

The ACGIH gives these limits in units of WBGT (wet bulb globe temperature) degrees Celsius (°C). The WBGT unit  considers environmental factors, such as air temperature, humidity and air movement, which contribute to the perception of hotness by people. WBGT values are not the same as humidex values. In some workplace situations, solar load (heat from radiant sources) is also considered in determining the WBGT. More details about WBGT are available below.

The ACGIH publication " 2022 TLVs® and BEIs®" (or the most current booklet) provides recommended screening criteria for heat stress exposure for workers (Table1). This publication and the "Documentation of TLVs® and BEIs®" should be consulted for more detailed information on these screening criteria, categories of work demands, guidelines for limiting heat strain and heat strain management.

Table 1
ACGIH Screening Criteria for Heat Stress Exposure (WBGT values in °C) 
for 8 hour work day five days per week with conventional breaks
Allocation of Work in a Work/Rest CycleAcclimatizedAction Limit (Unacclimatized)
LightModerateHeavyVery HeavyLightModerateHeavyVery Heavy
75-100%31.028.0----28.025.0----
50-75%31.029.027.5--28.526.024.0--
25-50%32.030.029.028.029.527.025.524.5
0-25%32.531.530.530.030.029.028.027.0

Notes:

Assumes 8-hour workdays in a 5-day workweek with conventional breaks.
TLVs assume that workers exposed to these conditions are adequately hydrated, are not taking medication, are wearing lightweight clothing (long-sleeve shirts and pants) and are in generally good health.

Examples of workloads:

Rest - sitting (quietly or with moderate arm movements)

Light work - sitting or standing to control machines; performing light hand or arm work (e.g. using a table saw); occasional walking; driving

Moderate work - walking about with moderate lifting and pushing or pulling; walking at moderate pace; e.g. scrubbing in a standing position

Heavy work - pick and shovel work, digging, carrying, pushing/pulling heavy loads; walking at fast pace; e.g. carpenter sawing by hand

Very Heavy - very intense activity at fast to maximum pace; e.g. shovelling wet sand

Adapted from:  2022  TLVs® and BEIs® - Threshold Limit Values for Chemical Substances and Physical Agents and Biological Exposure Indices. Cincinnati: American Conference of Governmental Industrial Hygienists (ACGIH), 2022 , p. 233 .

How do I use the heat stress exposure table (Table 1)?

Back to top

As an example, the wet bulb globe air temperature was measured with a WBGT direct reading meter at 27.0ºC for an 8-hour work period.  The worker is not used to hot conditions (i.e., unacclimatized) and is performing moderate cleaning duties (e.g., scrubbing floors and walls). These ACGIH guidelines suggest that an unacclimatized worker can do this work for approximately 25 to 50% of an 8-hour workday.  A "rest break" includes other job duties. Duties involving high activity or exertion levels may not allow a person’s body to cool effectively and should be avoided during the rest period. When it is very hot, the breaks should be distributed appropriately (e.g., shorter breaks every hour) rather than working for a longer time and taking longer breaks. 
See below for more information about controls and acclimatization.

The ACGIH exposure limits are intended to protect most workers from heat-related illnesses. The limits are higher than they would have been if they had been developed to prevent discomfort. If you are wearing heavier clothing then the exposure limit should be lowered. ACGIH recommendations for such situations are suggested in Table 2.

Table 2
Correction of TLV for Clothing
(Values cannot be added when wearing multiple layers)
Clothing TypeWBGT Correction (°C)
Work clothes (long sleeve shirt and pants)0
Cloth (woven material) coveralls0
SMS (Spunbonded - Meltdown - Spunbonded) polypropylene coveralls+ 0.5
Polyolefin coveralls+ 1
Double-layer woven clothing+ 3
Limited-use vapour-barrier coveralls+ 11
Note: These values are not to be used for completely encapsulating suits. Coveralls assume only modest clothing is underneath, not a second layer of clothing.
Adopted from: 2022 TLVs® and BEIs®: Threshold Limit Values for Chemical Substances and Physical Agents and Biological Exposure Indices. Cincinnati, Ohio: American Conference of Governmental Industrial Hygienists, 2022 p.  232

For example, an acclimatized worker wearing double-layer woven clothing doing moderate work at a WBGT of 28°C would have a corrected exposure level of 28.0 + 3 = 31°C, which would lower their allowable exposure to 0-25% work (from 75 -100% work). If the measured WBGT is 30°C, then the adjusted WBGT value would be 33°C and would be over the screening value for moderate work at a work/rest cycle of 0 – 25%. If work is done in these conditions, the employer should monitor the workers for heat strain and implement controls as needed.


What control measures can be used to reduce the effects of heat?

Back to top

The risk of heat-related illnesses can be reduced by:

  • Engineering controls to provide a cooler workplace.
  • Safe work practices to reduce worker exposure.
  • Training employees to recognize and prevent heat illnesses.

Table 3 (below) provides a summary of these controls.

Engineering Controls

Engineering controls are the most effective means of reducing excessive heat exposure. The examples which follow illustrate some engineering approaches to reducing heat exposure.

  • Reducing Metabolic Heat Production (heat produced by the body): Automation and mechanization of tasks minimize the need for heavy physical work and the resulting buildup of body heat.
  • Reducing the Radiant Heat Emission from Hot Surfaces: Covering hot surfaces with sheets of low emissivity material such as aluminum or paint that reduces the amount of heat radiated from this hot surface into the workplace.
  • Insulating Hot Surfaces: Insulation reduces the heat exchange between the source of heat and the work environment.
  • Shielding: Shields stop radiated heat from reaching workstations. Two types of shields can be used. Stainless steel, aluminum or other bright metal surfaces reflect heat back towards the source. Absorbent shields, such as water-cooled jackets made of black-surfaced aluminum, can effectively absorb and carry away heat.
  • Ventilation and Air Conditioning: Ventilation, localized air conditioning, and cooled observation booths are commonly used to provide cool workstations. Cooled observation booths allow workers to cool down after brief periods of intense heat exposure while still allowing them to monitor equipment.
  • Reducing the Humidity: Air conditioning, dehumidification, and elimination of open hot water baths, drains, and leaky steam valves help reduce humidity.

Personal Protection

Ordinary clothing provides some protection from heat radiated by surrounding hot surfaces. Specially designed heat-protective clothing is available for working in extremely hot conditions. In hot and humid workplaces, light clothing allows maximum skin exposure and efficient body cooling by sweat evaporation.

Workers who move back and forth between very hot, dry indoor environments and cold winter outdoor environments find that long underwear moderates the extremes in temperatures.

Eye protection which absorbs radiation is needed when the work involves very hot objects, such as molten metals and hot ovens.

Work that requires the wearing of impermeable clothing presents an added heat burden as the clothing reduces the body's ability to dissipate heat. Under such circumstances, it is often necessary to reduce the exposure limit values of WBGT to levels below those appropriate for workers wearing light clothing.

Table 3
Summary of Control Measures
Methods of ControlActions
Engineering controls 
Reduce body heat productionMechanize tasks.
Stop exposure to radiated heat from hot objectsInsulate hot surfaces. Use reflective shields, aprons, remote controls.
Reduce convective heat gainLower air temperature. Increase air speed if air temperature below 35°C. Increase ventilation. Provide cool observation booths.
Increase sweat evaporationReduce humidity. Use a fan to increase air speed (movement).
Clothing 
 Wear loose clothing that permits sweat evaporation but stops radiant heat. Use cooled protective clothing for extreme conditions.
Administrative controls 
AcclimatizationAllow sufficient acclimatization period before full workload.
Duration of workShorten exposure time and use frequent rest breaks.
Rest areaProvide cool (air-conditioned) rest-areas.
WaterProvide cool drinking water.
Pace of WorkIf practical, allow workers to set their own pace of work.
First aid and medical careDevelop and implement emergency procedures. Assign one person trained in first aid to each work shift. Train workers in how to recognize symptoms of heat exposure in themselves and others.

Can we become acclimatized to hot environments?

Back to top

The body adapts to a new thermal environment by a process called acclimatization. Complete heat acclimatization generally takes six to seven days, but some individuals may need longer. Loss of acclimatization occurs gradually when a person is moved permanently away from a hot environment. However, a decrease in heat tolerance occurs even after a long weekend. As a result of reduced heat tolerance, it is often not advisable for anyone to work under very hot conditions on the first day of their return to work.

New employees should acclimatize before assuming a full workload. It is advisable to assign about half of the normal workload to a new employee on the first day of work and gradually increased over subsequent days.

Although well-trained, physically fit workers tolerate heat better than people in poor physical condition, fitness and training do not substitute for acclimatization.

Some medications interfere with acclimatization. For example, hypotensives (drugs causing low blood pressure), diuretics, antispasmodics, sedatives, tranquilizers, antidepressants and amphetamines decrease the body's ability to cope with heat. Workers should seek a doctor's advice on the suitability of a medication for them if they work in hot environments. Consumption of alcohol also interferes with acclimatization.


How can I prevent heat related illnesses?

Back to top

If practical, workers in hot environments should be encouraged to set their own work and rest schedules. Infrequent or irregular tasks such as emergency repairs of hot process equipment often result in heat exposure. Experienced workers can often judge heat strain and limit their exposure accordingly. Inexperienced workers may need special attention as they may continue to work beyond the point at which signs of heat strain appear.

People are generally unable to notice their own heat stress-related symptoms. Their survival depends on their coworker's ability to recognize these symptoms and seek timely first aid and medical help.

Salt and Fluid Supplements: A person working in a very hot environment loses water and salt through sweat. This loss should be compensated by water and salt intake. Fluid intake should equal fluid loss. On average, about one litre of water each hour may be required to replace the fluid loss. Plenty of cool (10-15°C) drinking water should be available on the job site and workers should be encouraged to drink water every 15 to 20 minutes even if they do not feel thirsty. Alcoholic drinks should NEVER be taken as alcohol dehydrates the body.

An acclimatized worker loses relatively little salt in their sweat and, therefore, the salt in the normal diet is usually sufficient to maintain the electrolyte balance in the body fluids. For unacclimatized workers who may sweat continuously and repeatedly, additional salt in the food may be used. Salt tablets are not recommended because the salt does not enter the body system as fast as water or other fluids. Too much salt can cause higher body temperatures, increased thirst and nausea. Workers on salt-restricted diets should discuss the need for supplementary salt with their doctor.

Sport drinks, fruit juice, etc: Drinks specially designed to replace body fluids and electrolytes may be taken but for most people, they should be used in moderation. They may be of benefit for workers who have very physically active occupations but keep in mind they may add unnecessary sugar or salt to your diet. Fruit juice or sport and electrolyte drinks, diluted to half the strength with water, is an option. Drinks with alcohol or caffeine should never be taken, as they dehydrate the body. For most people, water is the most efficient fluid for re-hydration.

Emergency Action Plan: In extreme environments, an emergency plan is needed. The plan should include procedures for providing affected workers with first aid and medical care.

More information is available in our OSH Answers document Extreme Hot or Cold Temperature Conditions.


How do I calculate the WBGT Index?

Back to top

The wet bulb globe temperature (WBGT) is calculated by using the following equations.

  • For outdoors with direct sun exposure:

WBGT = 0.7 x Tempwet bulb + 0.2 x Tempglobe + 0.1 x Tempair

  • For indoors or outdoors without direct sun exposure:

WBGT = 0.7 x Tempwet bulb + 0.3 x Tempglobe

where:

Tempwet bulb = natural wet bulb temperature measured by using a thermometer whose bulb is covered with wet cotton cloth and is cooled by the natural air movement

Tempglobe = temperature measured using a black globe thermometer

Tempair = temperature measured using a conventional thermometer

All temperatures are to be expressed in °C.

Example

Workers employed in an outdoor workplace with direct exposure to the sun. Measurement of workplace conditions produced the following results.

Tempwet bulb = 24°C

Tempglobe = 42°C

Tempair = 40°C

WBGT = 0.7 x 24 + 0.2 x 42 + 0.1 x 40 = 29.2°C

Time-Weighted Average (TWA)

When thermal conditions of the workplace fluctuate widely, time-weighted average (TWA) WBGT is used to assess heat exposure.

TWA WBGT

WBGT1,WBGT2, etc. = the wet bulb globe temperatures measured or calculated

t1, t2, etc. = the elapsed time spent in the corresponding conditions described by WBGT1, WBGT2, etc., respectively.

Example

Measurement and/or calculation of WBGT during a two-hour job produced the following results.

Exposure duration 
(hours)
WBGT 
(°C)
0.525
1.027
0.528

These data would yield the following time-weighted average.

Formula

 


  • Fact sheet confirmed current: 2023-08-15
  • Fact sheet last revised: 2022-07-14